H20-8600™ SERIES LIQUID COOLING KITS CONTINUED... CUSTOMIZING YOUR OWN KIT FROM VARIOUS COMPONENTS Adding a second radiator is easy, and recommended in the following scenarios: Dual CPU setup: while operating dual CPU's with the basic single radiator kit is possible, the extra thermal load placed on the cooling system might require installing a stronger fan than that delivered with the kit, thus increasing audible noise. Adding a second radiator to the loop restores the proper balance between high performance and low noise offered by the basic H20-8600 kit. Extreme Overclocking: for enthusiast users seeking to squeeze extra Mhz from their microprocessors. Extremely quiet operations: where silent operations are preferred, adding a second ratiator will allow users to operate the fans at low speed, using a rheostat for example, while maintaining optimum processor temperature, even under substantial overclocks. Adding a second water-block for multiprocessor environments is easy: simply connected the second waterblock in series: the discharge from one to the inlet of the other. Adding VGA and/or chipset coolers follows the same rule as adding a second water-block: simply daisy chain the devices in series following the CPU water-block. Note concerning high-end VGA adapters, such as ATI® Raideon® 9700/9800 or nVidia® FX58/5900: it is suggested that adding a second radiator to the circuit will also enable higher overclocks with such graphic adpaters. The MCW50™ VGA cooler The MCW20™ chipset cooler Configuring the kit for 3/8" OD tubing: while it must be noted that 3/8" OD tubing will significantly reduce coolant flow-rate and affect cooling performance, such a configuration is possible, and sufficient in non or mildly overclocked systems: for example when users are mainly concerned with quiet operations. The following parts are then needed to adapt the kit to 3/8" OD tubing: Radiator : Part # PI0412S Pump, fill & bleed kit, and water-blocks: simply plug-in the following adapter into each 1/2" fitting, to reduce them to 3/8": For the MCW50 and MCW20 Use Part # PI061612S For the MCW6000 Use Part # PI0412S Example MCW50 back to top VERSIONS H20-8600-A Part # H20-8600-A for AMD® processors, includes: MCW6000-A™ water-block compatible with: AMD® Duron®, Athlon®, MP & XP, socket 462 Intel® Pentium® 3, socket 370 MCR80-F2 Radiator with (1) 80x80x25mm fans rated at 31.4 CFM and 28dbA, (2) worm-drive clamps MCP600™ 12 Volts DC industrial pump (connects directly to computer power supply ) FBK525™ fill and bleed kit assembly 12 feet 1/2" vinyl tubing, and tube inserts 2 Oz bottle HydrX™ extreme duty coolant Arctic Alumina™ thermal paste Coolsleeves™ Clear 40" length Set of two 3/8" tube to 1/2" tube OD quick-connect fittings (blue and red collets) Part # H20-8600-P for Intel® Pentium® 4 processors includes: MCW6000-P™ Intel® Pentium® 4, socket 478 compatible water-block MCR80-F2 Radiator with (1) 80x80x25mm fans rated at 31.4 CFM and 28dbA, (2) worm-drive clamps MCP600™ 12 Volts DC industrial pump (connects directly to computer power supply ) FBK525™ fill and bleed kit assembly 12 feet 1/2" vinyl tubing, and tube inserts 2 Oz bottle HydrX™ extreme duty coolant Arctic Alumina™ thermal paste Coolsleeves™ Clear 40" length Set of two 3/8" tube to 1/2" tube OD quick-connect fittings (blue and red collets)   Part # H20-8600-X for Intel® Xeon™ processors includes: MCW6000-PX™ Intel® Xeon™ compatible water-block MCR80-F2 Radiator with (1) 80x80x25mm fans rated at 31.4 CFM and 28dbA, (2) worm-drive clamps MCP600™ 12 Volts DC industrial pump (connects directly to computer power supply ) FBK525™ fill and bleed kit assembly 12 feet 1/2" vinyl tubing, and tube inserts 2 Oz bottle HydrX™ extreme duty coolant Arctic Alumina™ thermal paste Coolsleeves™ Clear 40" length Set of two 3/8" tube to 1/2" tube OD quick-connect fittings (blue and red collets)   Part # H20-8600-64 for AMD® Athlon® 64 & Opteron® processors includes: MCW6000-64™ AMD® Athlon® 64 & Opteron® compatible water-block MCR80-F2 Radiator with (1) 80x80x25mm fans rated at 31.4 CFM and 28dbA, (2) worm-drive clamps MCP600™ 12 Volts DC industrial pump (connects directly to computer power supply ) FBK525™ fill and bleed kit assembly 12 feet 1/2" vinyl tubing, and tube inserts 2 Oz bottle HydrX™ extreme duty coolant Arctic Alumina™ thermal paste Coolsleeves™ Clear 40" length Set of two 3/8" tube to 1/2" tube OD quick-connect fittings (blue and red collets) AJ00172 backing plate and retention frame Part # H20-8600-B "Bare" kit without water-block includes: MCR80-F2 Radiator with (1) 80x80x25mm fans rated at 31.4 CFM and 28dbA, (2) worm-drive clamps MCP600™ 12 Volts DC industrial pump (connects directly to computer power supply ) FBK525™ fill and bleed kit assembly 12 feet 1/2" vinyl tubing, and tube inserts 2 Oz bottle HydrX™ extreme duty coolant Arctic Alumina™ thermal paste Coolsleeves™ Clear 40" length Set of two 3/8" tube to 1/2" tube OD quick-connect fittings (blue and red collets)   Manufacturer Suggested Retail Pricing H20-8600 series liquid cooling kits Part # Processor compatibility MSRP US $ H20-8600-A™ AMD® socket A, Intel® socket 370, complete kit $215.00 H20-8600-P™ Intel® Pentium® 4, complete kit $215.00 H20-8600-X™ Intel® Xeon™, complete kit $217.50 H20-8600-64™ AMD® Athlon® 64 & Opteron® , complete kit $221.50 H20-8600-B™ Bare kit, no water-block included. $175.00 Add-On components & accessories Part # Description MSRP US $ MCW6000-A™ CPU Water-block Assembly for AMD® socket A, Intel® socket 370 $39.99 MCW6000-P™ CPU Water-block assembly for Intel® Pentium® 4 $39.99 MCW6000-PX™ CPU Water-block assembly for Intel® Xeon™ $42.50 MCW6000-64™ CPU Water-block Assembly for AMD® Athlon® 64 and Opteron® $42.50 See also MCW6000™ available spare parts   MCW50™ VGA Water-block assembly for ATI & nVidia VGA $38.95 MCW50-FX ™ MCW50 adapter kit for FX5800 and up series VGA $6.50 MCW20-A™ Chipset water-block for AMD® platforms $32.95 MCW20-P™ Chipset water-block for Intel® platforms $32.50 MCW20-R™ Chipset water-block for AMD® and Intel® platforms $37.95 FBK525™ R2 Fill & Bleed kit 525 fits in 5 1/4" bay $28.50 MCR80-F2™ Radiator with (1) 80x80x25mm fan and quick-connect adapters $59.95 MCR80™ Radiator alone $46.50 Y Connector kit 3/8" barb "Y" connector $2.60 MCP600™ 12 Volts Industrial Pump $84.95 MCP600-RK Reducer kit 1/2" barb to 3/8" ID tubing $2.21 Coolsleeves™ Clear 40" length $2.95 Please consult your Swiftech distributor prior to ordering direct from us, or purchase the product factory direct here <<PREVIOUS PAGE